In minting coins we have a number of very specific terms that ae often interchangeably used among collectors. The only way to combat this improper usage is through properly teaching these terms:
- Hub - A positive design tool used to press dies in the coin making process.
- Master hub - the actual engraving reduction from about 8 inches of working diameter to the size of a finished coin. This is the tool that begins the die making pyramid. It is the master tool of tools used to create other tools thaqt eventually make the coins.
- Master die - The second step in die making. This tool is a copy of the design used on the coins because it had the normal design pressed into it by the master hub, so by nature everything is recessed and backwards. Generally a dozen or so master dies are created using the master hub.
- Working hub - The third step in die making. Once master dies are made they are used in the hubbing press to create the working hubs, a bar of steel that has what looks like a normal coin relief because it is a direct opposite copy of the master die.
- Working die - the final step in die making and the final tool that is created to mint the coins. Each die makes on the order of a million coins (when discussing cents), and when they wear out or are broken, they are changed for new ones. It's right here that doublid dies occur. Dies are annealed in an oven to help the hubbing press leave a complete design on the die. Each time the die is placed back in the hubbing press it is perfectly aligned using the keys on the shoulder of the hub and die. When the die is not aligned properly with the previous hubbing, the design comes out doubled on that die. The die creates all of its coins with a doubled design - a doubled die.
- Blank - A flat, sheet cut round disc of metal intended to be made into a coin.
- Upset mill - the machine used to create the raised area all the way around the edge of the blank. This helps the flow of metal on the planchet during the coining process.
- Planchet - This is the disc of metal after it goes through the upset mill as a blank. After this process the planchet is ready to be fed into the coining press to become a coin.
- Strike - As a verb it is the process that makes coins. The dies strike the planchet to create a coin. As a noun, the strike describes the strength by which the coining press imparted the design onto the coin. A 'heavy strike' describes a coin with a full and complete design showing that the spacing between the dies in the press and the force used to make the coin were properly set.
- Coining press - This is the machine on which coins are made. The blanks are fed through the coinage press from a hopper, and the press mints the resulting coins up to 100 per minute.
- Die pair - One set of dies (obverse and reverse) used to mint coins together on the coining press.
- Die marriage - the term used to describe which obverse and which reverse were used as a pair to mint a coin.
- Flow lines - microscopic lines in the die surface created by very small bits of steel chipping away from the surface of the die and crawl outward along the face of a die like rain on a windshield as more coins are struck.
- Die state - Measurement of the amount of wear and tear on a die as evidenced by the loss of detail and the amount and severity of flow lines in the design on the die, especially near the rim. Die state begins with the first coin struck when the die has a very sharp design and is called Very Early Die State (VEDS) - Very few coins are struck before the first signs of wear set in thus “aging” the die to Early Die State (EDS). More wear comes with more strikes, and when a light to moderate noticeable amount of wear has come onto the die, it is then called Mid Die State (MDS). As the die continues to age to a very worn status with minor loss of detail on the coins minted it is called Late Die State (LDS). Very Late Die State (VLDS) is used when coins were minted with a die that is so damaged by flow lines that small details of the design on the die are completely gone and the outer edges of most of the details are shaggy and rough.
- Die stage - A term relating to the progression of a die while minting coins. Because die varieties are always specific to a single die, damage to that die can be followed in steps. Collectors assemble these with the earliest markers described as Stage A. Every marker found subsequent to the new die adds a stage.
- Die variety - An amount of flaw in the design imparted on the die by errant alignment in the hubbing press or in the mint mark tooling. This is specific to individual dies, usually involves doubling of some degree on the die itself, and can be cataloged by assigning dies numbers and comparing coins to the attributes of the doubling and/or markers on the die or on other coins known to have been minted by one specific pair of dies.
- Design variety - A different term altogether that describes not a single die, but all of the dies made with a specific date, mint mark and design. As the design is re-engraved and introduced into the die making process to freshen the design used, the design is modified, usually in very minor ways and can be cataloged as design types. When two or more design types are used simultaneously on a single issue of coins, we call the distinction of those two designs in a single issue a design variety. An example is that the 1960 small date and large date designs compared to one another is a design variety.
- Mint error - Caused by a flaw in how planchets are made, how the press strikes the coins, or by damage created to the die which is not immediately corrected. All mint errors are readily noticeable on the coins made except for composition type mint errors which sometimes may require a scale to tell the difference. Machine doubling, die chips and minor cracks, and design elements reduced in relief or removed altogether are curiosities which are considered a normal part of minting coins and not mint errors.